|
|
|
 |
|
|
|
|
Walthers GOO Glue
GOO is the All-Purpose adhesive that grips almost anything. It never lets go. GOO is perfect for building or repairing jobs on your layout and around the house. The easy contact action of GOO produces fast-setting joints with any material. GOO works with all types of metals including steel, brass, aluminum, copper and more. It also works on plastic, wood cardboard, china, leather, vinyl, ceramics, paper, concrete and many more surfaces. GOO is a permanent rubber base adhesive that's shockproof-it's as flexible as rubber. Joints won't crack when flexed back and forth, won't break loose when the temperature changes and won't weaken when wet or damp. It sticks forever!
Part # WAL-299
$3.19
Click the photo to order
|
|
|
|
|
|
|
BSI Insta-Cure Thin CA Adhesive
INSTA-CURE™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
1/2 oz.
Part # BSI-101
$2.39 Sale 1.99
Click the photo to order
|
|
|
|
|
|
|
BSI Insta-Cure Thin CA Adhesive
INSTA-CURE™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
1 oz.
Part # BSI-102
$3.99 Sale 2.49
Click the photo to order
|
|
|
|
|
|
|
BSI Insta-Cure+ Med. CA Adhesive
INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
1/2 oz.
Part # BSI-106
$2.39 Sale 1.99
Click the photo to order
|
|
|
|
|
|
|
BSI Insta-Cure+ Med. CA Adhesive
INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
1 oz.
Part # BSI-107
$3.99 Sale 2.49
Click the photo to order
|
|
|
|
|
|
|
BSI Maxi-Cure Thick CA Adhesive
MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars.
1/2 oz.
Part # BSI-111
$2.69 Sale 2.39
Click the photo to order
|
|
|
|
|
|
|
BSI Maxi-Cure Thick CA Adhesive
MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic. MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars.
1 oz.
Part # BSI-112
$4.39 Sale 3.99
Click the photo to order
|
|
|
|
|
|
|
BSI Super-Gold Thin Odorless Foam Safe CA Adhesive
SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
1/2 oz.
Part # BSI-121
$5.59 Sale 4.49
Click the photo to order
|
|
|
|
|
|
|
BSI Super-Gold Thin Odorless Foam Safe CA Adhesive
SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
1 oz.
Part # BSI-122
$10.39 Sale 8.99
Click the photo to order
|
|
|
|
|
|
|
BSI Super-Gold+ Med. Odorless Foam Safe CA Adhesive
SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
1/2 oz.
Part # BSI-126
$5.59 Sale 4.89
Click the photo to order
|
|
|
|
|
|
|
BSI Super-Gold+ Med. Odorless Foam Safe CA Adhesive
SUPER-GOLD™ and SUPER-GOLD+™ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
1 oz.
Part # BSI-127
$10.39 Sale 8.99
Click the photo to order
|
|
|
|
|
|
|
BSI Insta-Set with Pump Sprayer
INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.
2 fl. oz.
Part # BSI-151
$3.99 Sale 3.49
Click the photo to order
|
|
|
|
|
|
|
BSI Un-Cure CA Debonder
UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water.
1 oz.
Part # BSI-161
$2.39 Sale 1.99
Click the photo to order
|
|
|
|
|
|
|
Plastruct Plastic Weld
A colorless, liquid, plastic-fusing adhesive. Dissolves a thin layer of each surface to form a welded joint as strong as the surrounding area. Bonds styrene, ABS, butrate and acrylics.
Part # PLS-2
$3.59
Click the photo to order
|
|
|
|
|
|
|
Plastruct Bondene
A colorless, liquid, plastic-fusing adhesive. Dissolves a thin layer of each surface to form a welded joint as strong as the surrounding area. Bonds Styrene to Styrene, ABS to ABS and most other alike plastic combinations.
Part # PLS-3
$3.59
Click the photo to order
|
|
|
|
|
|
|
Testors Clear Parts Cement Window Maker
Model Master Cement is a wonderful choice when needing glue. We have a wide range of glues that cover almost every gluing needs. For professional results each time, use non-crazing Clear Parts Cement & Window Maker. This glue is best used for. clear polystyrene parts like canopies, windows and windshields, and lenses to your plastic model kit.
- will not craze plastic
- does not yellow or leave unsightly residue.
- non-toxic, washes up with water(before it dries) if spills occur on your model.
Part # Test-8876C
$3.69
Click the photo to order
|
|
|
